Copyright 2010 SDAdish.com All Rights Reserved.

3ABN Proclaim Move

DO NOT MOVE YOUR SATELLITE DISH!

3ABN Proclaim is changing location on the G-19 satellite.  You may need to program this channel change into your receiver.

Please note that if you have had the AON channel for more than three months, the Proclaim! Channel is taking its place and you do not need to make these changes unless you want the names in your channel banner to match the current channel saying Proclaim.

General Instructions For Any Reciever:
Step one:
Enter the menus for organizing or editing the Channels or Services.
Delete the old 3ABN Proclaim channel

Step two:
Go to the installation menus and enter the channel or service search or scan. Some receivers may have a TP scan option. Enter the following parameters if they aren't already in the boxes:

Frequency: 11842
Symbol Rate: 22000
Polarization: Horizontal

Look at the bottom of the list sometimes there are different functions assigned to the four colored buttons on the remote control. You want TP scan. If you manage to scan the entire satellite you will have over 200 Video channels in many different languages. Enter the menu for organizing or editing the Channels or Services, highlight all the channels you don't want to watch, Delete them. Thus leaving just the 3ABN channels plus the others you may want to watch.

GeoSatPro MicroHD:




Lexium DBS6600 & DBS7000:





Topfield 3000, 4000 & 6200:




Step one:
Delete the existing Proclaim channel. You can follow this part of the instructions after you finish if you want to delete any other channel that you don't want. If you delete them now they may be added back in step two.
Press [MENU] and [Down Arrow] to select ORGANIZING SERVICES then press [OK].
Press [Down Arrow] to select DELETE and press [OK].
Use the [Up Arrow] and [Down Arrow] keys to select 3ABN PROCLAIM and press [OK]. It will be marked for deletion and turn gray.
Press [EXIT] and confirm deletion by pressing [Left Arrow] and [OK].

Step two:
Rescan to get ALL the channels, including Proclaim channel back.
Press [Down Arrow] to select INSTALLATION and press [OK].
Press [Down Arrow] to select CHANNEL SEARCH or SERVICE SEARCH and press [OK].
Set the parameters as follows using the four [Arrow] keys and the number pad on the remote:

Satellite Name (depending on the software in the receiver could be one of the following): AMC_5(Ku), IntelAmc_5(Ku), IntelAmer_5(Ku), or Telstar5(Ku)
Search mode: Manual [Right Arrow]
Frequency: 11842 MHz
Symbol Rate: 22000 KS/s
Polarization: Horizontal [Right Arrow]
Network Search: On [Right Arrow]
FTA/Scrambled: FTA Only [Right Arrow]

Highlight START SEARCH and press [OK].
When the search is complete a box will pop up asking you to press [OK].
Press [EXIT].
You are now finished. You may follow the instructions in step one to delete unwanted channels

Manhattan 1500:
Step one:
Delete the existing Proclaim channel. You can follow this part of the instructions after you finish if you want to delete any other channel that you don't want. If you delete them now they may be added back in step two.
[SETUP] [DOWN CH] select EDIT CHANNEL LIST [OK]
With the upper button in the center highlighted press [VOL RT] until it says DELETE then press [OK]
using the [CH up/down] and [pg up/down] buttons select the Proclaim! Channel and press [OK] twice. This will mark the channel for deletion.
[CH down] to "STORE" and press [OK].
[ESC] to return to the picture.

Step two:
Rescan to get the Proclaim! Channel back in your line up.
Press [SETUP] [CH down] to highlight CHANNEL SEARCH and press [OK].
Using the number pad and arrow keys on the remote, set the table as follows:

TP Freq.: 11842
Polarization: Hor.
Skew: Off
Symbol Rate: 22000
Advanced: Show Menu
Search Option: All

Signal strength should be green
Press [CH down] to select "START SEARCH" and press [OK].
Select "STORE" and press [OK].

You are now finished. You may follow the instructions in step one to delete unwanted channels.

Manhattan 1000:



Step one:
Delete the existing Proclaim channel. You can follow this part of the instructions after you finish if you want to delete any other channel that you don't want. If you delete them now they may be added back in step two.
Press [MENU] [VOL right] to select EDIT CHANNEL on the icons on the top.
Highlight CHANNEL EDIT in the list on the left and press [OK].
With the upper button in the center highlighted press [VOL right] until it says DELETE then press [OK].
Using the [CH up/down] and [PAGE up/down] buttons select the Proclaim! Channel and press [OK] twice. This will mark the channel for deletion.
Press [ESC] [CH down] to highlight STORE and press [OK].
Press [MENU]

Step two:
Scan for the Channels back into your list.
Press [MENU] [VOL right] to select INSTALL on the icons at the top of the screen.
Press [CH down] to select CHANNEL SEARCH and press [OK]
Press [CH down] to highlight TP DATA and press [OK] this will open a box on the right of the screen.
Press [VOL right] to go to TP2 on the top line of the TP DATA box set the Freq. and S/R to 0 using the number keys on the remote.
Press [CH down] to select "STORE" and press [OK].
With TP DATA still highlighted press [OK] and using the arrow and number keys on the remote set the parameters as follows:

Freq.: 11842
Polarity: Horiz.
S/R: 22000
FEC: ¾ or AUTO

Press [CH down] to select "STORE" and press [OK] and the box will close.
Press [CH down] to select "START" and press [OK].
You may go back to step one to delete other unwanted channels.

Pansat 300A:
DO NOT move your satellite dish.
Step one:
Delete the existing Proclaim channel. You can follow this part of the instructions after you finish if you want to delete any other channel that you don't want. If you delete them now they may be added back in step two.
Press [Menu] select CHANNEL EDITING "TV" and press [OK].
Enter the password as 0000.
Use the [VOL right] button to select the "X" icon at the top of the screen and press [OK].
Use the [CH up] and [CH down] buttons to select 3ABN Proclaim and press [OK].
Confirm deletion by pressing [OK].
Press [MENU] to return to the main menu.

Step two:
Scan the Proclaim! Channel back into your channel list.
Press [VOL down] to select INSTALLATION and press [OK].
Enter the password 0000.
Press the [VOL down] to select TP EDIT/SCAN and press [OK].
Using the up/down/left/right arrow buttons and the number keys on the remote control, enter the following information:

Satellite Name: Telstart 5/Ku
TP Frequency: 11,842 GHz (left/right arrow should get you this)
Polarization: Horizontal 18V
Symbol Rate: 22,000 MSPS
Scan: Free Only

Highlight the SCAN line and press [OK].
When the list of channels shows up press [OK] to save.
You are now finished. You may follow the instructions in step one to delete unwanted channels.

Sun - Thurs 7am-7pm PT
          Fri 7am-3pm

MicroHD Video
Topfield Video
Manhattan1000 Video
Lexium Video